Ge Refrigerator Serial Numberaz401556
This temperature sensor, also known as a thermistor, is used for refrigerators and freezers. The sensor sends the temperature reading of the refrigerator towards the control board. If your refrigerator or freezer runs too long, is too warm, will not defrost, or has sections that are too cold, replacing this part is the solution. Before replacing the temperature sensor, make sure to unplug the fridge for safety. The tools needed for this repair are a nut driver, wire crimper, and wire splice connectors. Search your model number to ensure the correct part is ordered and refer to model specific diagrams/owners manual for the exact instructions. This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer.
The slide supports the front drum as the drum rotates. Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 slides per dryer. The drum bearing slide may need to be replaced if the dryer is not tumbling, takes longer than usual to dry clothes, or is noisy during use. This is a white plastic part that is sourced directly from the manufacturer. Sold individually.
The drum slides support the front of the dryer drum. As they start to break down it may cause your dryer to make noise or not dry clothes in the usual amount of time. You will need to purchase two for both sides of your dryer. They attach to the outer-most sides of the bearing. The manufacturer recommends replacing both slides at the same time. Take this opportunity to clean out the lint and dust in the dryer, to keep it running smoothly.
This is a genuine replacement part that comes directly from the manufacturer. This item is sold individually.
Side-by-Side Refrigerators
This is a replacement ice maker kit, it is used in the freezer section of your refrigerator. This particular model will produce seven round or crescent shaped cubes every cycle. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level and ice is still not being made it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need.
Microwaves
This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connector, tube and fill cup. Before you start this repair, you should shut off the water supply and unplug your appliance. Please note, when you have installed your new ice maker it can take up to 24 hours for it to begin producing ice. This is a dryer drum drive belt.
It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps around the drum and a tensioner pulley, and spins the drum as the motor rotates. Your dryer drum cannot spin without this belt.
Belts can stretch or become brittle over time which may cause it to malfunction. This is an original manufacturer replacement part.
Be sure to use work gloves to protect your hands from sharp internal parts during this repair. The rack slide end cap is the part that attaches to the rails of your upper dish rack and prevents the dishrack from sliding too far out. If you find the dish rack is causing the door to not close properly, it may be due to the part being worn out or damaged. All you need to complete this repair is a small flat blade screw driver.
Simply pop out the cap and snap the new one into place. If the rear cap needs to be replaced you will need to remove both front caps and slide the rack completely off for full access. The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the switch. The switch is spring loaded and is a generally closed type of switch meaning there should be no continuity when the button is depressed, and continuity through the switch when the button is not depressed. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace.
The repair usually takes less than 15 minutes and requires a flat blade screwdriver and needle nose pliers. If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected.
You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut driver to complete this repair. This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised.
Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer. This is an ice and water filter. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water.
This also may lead to your refrigerator not dispensing water or ice properly. Manufacturers recommend you change your filter every six months to ensure it properly filters impurities. This will also ensure a normal dispensing rate. Note: As per the manufacturer, this is an updated water filter. If you have never installed the updated part or your old model was made by Culligan, you may need the adapter to install the filter. See related parts.
This filter is sold individually.